Javascript required
Skip to content Skip to sidebar Skip to footer

Sonata Reading Only Image Files on Usb

You are using an out of appointment browser. Information technology may not brandish this or other websites correctly.
Y'all should upgrade or use an culling browser.
  • #i
HI,
i have Amilogic M805, Wifi is AP6212
on the board is: Netxeon MK808Q_V10-20140822
On the cover is MINI Goggle box grade android Quad - Core MK808B Plus

If i tried USB_Burning_Tool
I have fault [0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
Why ?

  • #2
HI,
i have Amilogic M805, Wifi is AP6212
on the lath is: Netxeon MK808Q_V10-20140822
On the cover is MINI TV course android Quad - Core MK808B Plus

If i tried USB_Burning_Tool
I have fault [0x10105002]Romcode/Initialize DDR/Read initialize condition/USB Control setup fault
Why ?

I had the same trouble with S905 when use defective usb flashing cablevision. and try redownload firmware
  • #three
I had the same problem with S905 when use defective usb flashing cable. and effort redownload firmware

i try 2 cables and two computers
windows 10 64bit
a windows xp 32bit

same mistake.

  • #4
I had same problem with M8S android box, through trial and error and an 60 minutes of pulling my hair out, I tried this, Amlogic called-for tool, Toothpick method and male to male person usb cable. (Go out toothpick in AV hole )Later releasing the toothpick and pressing start the error comes up after 2% I apace pressed the toothpick in once more to see what would happen and boom it started to burn down the firmware on, mayhap luck i dont know only box support running.. Hope it works for others..Des
  • #5
how you lot gear up that mistake? Romcode/Initialize DDR/Read initialize condition/USB Control Setup Error
  • #6
Same problem with MXIII 4k =(
  • #seven
Had the same problem, shortened the USB cable (that i made myself) to 15Cm, so it worked, point integrity ?
  • #8
first put the rom y'all will use, and then printing start, only then plug the device into the USB port. Worked with me having the same problems.
code4power
  • #9
work for me... redownload firmware
  • #10
Code4power, a link please for download the img
  • #eleven
Had same outcome with MXS Plus unit.... Tried a different USB-USB cable and now up and running. MANY THANKS TO ALL ON Here
  • #12
uncheck erase flash and bootloader in amlogic tool and that should ready your trouble
  • #13
uncheck erase flash and bootloader in amlogic tool and that should fix your problem

Worked like a charm. Thanks
  • #15
I cannot get past that error. I take tried 3 unlike computers and diverse different versions of the called-for tool equally well equally unchecking the boxes suggested higher up. So frustrating.
  • #16
x96pro +
I cannot get past that fault. I have tried 3 different computers and various dissimilar versions of the burning tool too as unchecking the boxes suggested higher up. Then frustrating.

I had the same bug as described to a higher place, and I simly just changed the cable lenght from 1.5m to 30cm and the box started flashing itself from the burning tool! :)

  • #17
I got a shorter cablevision only it still does it for me :(
  • #eighteen
So guys afterward going crazy did this - Tried the Nand Method on a95x. Sequence - Upload your prototype to USB burning tool (don't hit showtime) - connect USB A to A cable (didn't connect) - Flash Pins five-six or 6-seven - At present USB tools see's the box but don't hit start yet - considering usb power is not enough to burn information technology - Now insert the toothpic to hit the reset button - At present connect ability while toothpic is inserted - Viola - the box starts burning - This is a sure to work method - everytime.
  • #19
So guys subsequently going crazy did this - Tried the Nand Method on a95x. Sequence - Upload your image to USB burning tool (don't hit start) - connect USB A to A cable (didn't connect) - Flash Pins 5-6 or vi-7 - Now USB tools encounter's the box but don't hit showtime yet - considering usb power is not plenty to burn it - Now insert the toothpic to striking the reset button - Now connect power while toothpic is inserted - Viola - the box starts burning - This is a certain to work method - everytime.
Love, i tried this method as well...just no luck. please advice..., if possible please share the link for usb burning tool and the firmware for MXQ PRO+ model. Will try fresh. Would highly appreciate ur help...
J0kker
  • #20
Had the same problem with mecool km9.
Tried all with no luck, then i tried to disconnect the box, close then restart usb called-for tool, load the img file, unchecked erase flash and erase bootloader, hold the reset push with toothpic, then connect the box, striking refresh, and after that, start the flashing procedure.
Then, if you tried to uncheck erase... like i did, y'all should attempt to disconnect the box, as it doesn't seem to register the unchecking without that.
:expert:

Yous can meet how many failed i had before disconnecting/reconnecting the box !

Similar threads

sam298

mcilwraiththrooked.blogspot.com

Source: https://forum.xda-developers.com/t/usb_burning_tool-error.3321735/